机械术语词汇列表
| 1 | 除油过滤器 | air remover |
|
| 2 | 轴面分速度 | axial plane component of velocity |
|
| 3 | 反转液力变矩器 | backward running torque converter |
|
| 4 | 中间流线 | center line of flow path |
|
| 5 | 齿宽系数 | coefficient of facewidth |
|
| 6 | 最大变形量系数 | coefficient of maximum deflection |
|
| 7 | 凸缘螺钉 | collar screw |
|
| 8 | 曲度系数 | curvature correction factor |
|
| 9 | 正车齿面 | drive side |
|
| 10 | 从动带轮 | driven pulley |
|
| 11 | 涡轮液力转矩 | hydraulic torque of turbine |
|
| 12 | 内锥距 | inner cone distance |
|
| 13 | 接触线;瞬时接触线 | line of contact |
|
| 14 | 长手柄套 | long sleeve knob |
|
| 15 | 带浮动间隔环的机械密封 | mechanical seal with floating intermediate ring |
|
| 16 | 最小油膜厚度 | minimum oil film thickness |
|
| 17 | 制动副数 | number of braking pairs |
|
| 18 | 相位转换工况点 | phase position condition cut-over |
|
| 19 | 平面包络环面蜗杆 | planar double enveloping worm |
|
| 20 | 气动逻辑控制元件 | pneumatic logic control components |
|
| 21 | 长幅系数 | prolate ratio |
|
| 22 | 阻封流体 | quench fluid |
|
| 23 | 带附件的滚子链 | roller chain with attachments |
|
| 24 | 整定处理 | setting |
|
| 25 | 带肩销轴 | shouldered |
|
| 26 | 单导程圆柱蜗杆 | single lead cylindrical worm |
|
| 27 | 波纹手轮 | sinuate handwheel |
|
| 28 | 转动小手柄 | small handle with sleeve |
|
| 29 | 球面渐开螺旋面 | spherical involute helicoid |
|
| 30 | 花键联接 | spline coupling |
|
| 31 | 带轮毂链轮 | sprocket with hub |
|
| 32 | 直齿轮副 | spur gear pair |
|
| 33 | 零速工况 | stall condition |
|
| 34 | 零矩工况 | stall torque condition |
|
| 35 | 顶锥角;顶圆锥角 | tip angle |
|
| 36 | 端面作用角 | transverse angle of transmission |
|
| 37 | 积极控制式波发生器 | wave generator of positive control |
|
| 38 | 针齿套 | wheel roller |
|
| 39 | 宽面法兰 | wide contact face flange |
|
| 40 | 蜗杆轮齿 | worm thread |
|
生词本打印版
| 1 | air remover | 除油过滤器 | |
| 2 | axial plane component of velocity | 轴面分速度 | |
| 3 | backward running torque converter | 反转液力变矩器 | |
| 4 | center line of flow path | 中间流线 | |
| 5 | coefficient of facewidth | 齿宽系数 | |
| 6 | coefficient of maximum deflection | 最大变形量系数 | |
| 7 | collar screw | 凸缘螺钉 | |
| 8 | curvature correction factor | 曲度系数 | |
| 9 | drive side | 正车齿面 | |
| 10 | driven pulley | 从动带轮 | |
| 11 | hydraulic torque of turbine | 涡轮液力转矩 | |
| 12 | inner cone distance | 内锥距 | |
| 13 | line of contact | 接触线;瞬时接触线 | |
| 14 | long sleeve knob | 长手柄套 | |
| 15 | mechanical seal with floating intermediate ring | 带浮动间隔环的机械密封 | |
| 16 | minimum oil film thickness | 最小油膜厚度 | |
| 17 | number of braking pairs | 制动副数 | |
| 18 | phase position condition cut-over | 相位转换工况点 | |
| 19 | planar double enveloping worm | 平面包络环面蜗杆 | |
| 20 | pneumatic logic control components | 气动逻辑控制元件 | |
| 21 | prolate ratio | 长幅系数 | |
| 22 | quench fluid | 阻封流体 | |
| 23 | roller chain with attachments | 带附件的滚子链 | |
| 24 | setting | 整定处理 | |
| 25 | shouldered | 带肩销轴 | |
| 26 | single lead cylindrical worm | 单导程圆柱蜗杆 | |
| 27 | sinuate handwheel | 波纹手轮 | |
| 28 | small handle with sleeve | 转动小手柄 | |
| 29 | spherical involute helicoid | 球面渐开螺旋面 | |
| 30 | spline coupling | 花键联接 | |
| 31 | sprocket with hub | 带轮毂链轮 | |
| 32 | spur gear pair | 直齿轮副 | |
| 33 | stall condition | 零速工况 | |
| 34 | stall torque condition | 零矩工况 | |
| 35 | tip angle | 顶锥角;顶圆锥角 | |
| 36 | transverse angle of transmission | 端面作用角 | |
| 37 | wave generator of positive control | 积极控制式波发生器 | |
| 38 | wheel roller | 针齿套 | |
| 39 | wide contact face flange | 宽面法兰 | |
| 40 | worm thread | 蜗杆轮齿 |
