1 | 平衡入水值 | Balanced Gate Value |
|
2 | 前模镶件 | cavity sub-insert |
|
3 | 清理,清除,清扫 | clean-up |
|
4 | 牵引曲面 | draft surface |
|
5 | 凝固与熔范围 | freezing range |
|
6 | 气辅注射成型 | gas assisted injection molding |
|
7 | 磨擦;磨碎;磨光 | grind |
|
8 | 磨砂使用的轮子 | grinding wheel |
|
9 | 胚头螺丝 | hex screws |
|
10 | 热浇口套 | Hot Sprue Bushing |
|
11 | 内部空腔 | internal void |
|
12 | 起重螺丝,千斤顶 | jacking screw |
|
13 | 啤机吨数 | machine size |
|
14 | 模具型腔 | mold cavity |
|
15 | 模具日志镶件 | Mold Dating Insert |
|
16 | 内模编号 | No of cavities |
|
17 | 热嘴垫圈 | nozzle seat |
|
18 | 平行块 | parallel |
|
19 | 披锋 | parting line flash |
|
20 | 前后模接触面 | parting line shutoff |
|
21 | 气路控制器 | pneumatic controller |
|
22 | 喷头螺丝 | set screw |
|
23 | 轻度磨砂 | slight stoning |
|
24 | 凝固收缩率 | solidification shrinkage |
|
25 | 球刀 | spherical mill |
|
26 | 球头拉料杆 | sprue puller,ball-headed |
|
27 | 潜水口 | submarine gate |
|
28 | 平面仪 | surface |
|
29 | 啤把锁 | tapered interlocks(round [$ rectangular) ] |
|
30 | 热扩散性能 | thermal diffusivity |
|
31 | 热电偶连结头 | thermocouple connector |
|
32 | 热塑性塑料热塑性 | thermoplastic |
|
33 | 热固性塑料. 热固性 | thermoset |
|
34 | 切换式早期回撞装置 | togglelock early ejector return |
|
35 | 模具名称 | tool name |
|
36 | 模具来源 | tool source |
|
37 | 模具钢材 | tool steel |
|
38 | 排气式注塑成型 | vented injection molding |
|
39 | 黏度,黏性 | viscosity |
|
40 | 耐磨片 | wear plate |
|
1 | Balanced Gate Value | 平衡入水值 | |
2 | cavity sub-insert | 前模镶件 | |
3 | clean-up | 清理,清除,清扫 | |
4 | draft surface | 牵引曲面 | |
5 | freezing range | 凝固与熔范围 | |
6 | gas assisted injection molding | 气辅注射成型 | |
7 | grind | 磨擦;磨碎;磨光 | |
8 | grinding wheel | 磨砂使用的轮子 | |
9 | hex screws | 胚头螺丝 | |
10 | Hot Sprue Bushing | 热浇口套 | |
11 | internal void | 内部空腔 | |
12 | jacking screw | 起重螺丝,千斤顶 | |
13 | machine size | 啤机吨数 | |
14 | mold cavity | 模具型腔 | |
15 | Mold Dating Insert | 模具日志镶件 | |
16 | No of cavities | 内模编号 | |
17 | nozzle seat | 热嘴垫圈 | |
18 | parallel | 平行块 | |
19 | parting line flash | 披锋 | |
20 | parting line shutoff | 前后模接触面 | |
21 | pneumatic controller | 气路控制器 | |
22 | set screw | 喷头螺丝 | |
23 | slight stoning | 轻度磨砂 | |
24 | solidification shrinkage | 凝固收缩率 | |
25 | spherical mill | 球刀 | |
26 | sprue puller,ball-headed | 球头拉料杆 | |
27 | submarine gate | 潜水口 | |
28 | surface | 平面仪 | |
29 | tapered interlocks(round [$ rectangular) ] | 啤把锁 | |
30 | thermal diffusivity | 热扩散性能 | |
31 | thermocouple connector | 热电偶连结头 | |
32 | thermoplastic | 热塑性塑料热塑性 | |
33 | thermoset | 热固性塑料. 热固性 | |
34 | togglelock early ejector return | 切换式早期回撞装置 | |
35 | tool name | 模具名称 | |
36 | tool source | 模具来源 | |
37 | tool steel | 模具钢材 | |
38 | vented injection molding | 排气式注塑成型 | |
39 | viscosity | 黏度,黏性 | |
40 | wear plate | 耐磨片 |