1 | 牙顶高 | addendum |
|
2 | 无石棉摩擦材料 | asbestos-free friction material |
|
3 | 黏-温斜率 | ASTM viscosity-temperature slope |
|
4 | 双向制动器 | bi-directional brake |
|
5 | 制动钢带 | brake steel belt |
|
6 | 沉头槽销 | countersunk grooved pin |
|
7 | 橡胶块联轴器 | coupling with rubber pads |
|
8 | 螺纹法兰 | crewed flange |
|
9 | 行程偏差 | deviation of stroke |
|
10 | 圆盘手柄套 | disc handle seat |
|
11 | 凹形变形 | dishing |
|
12 | 扁环螺母 | flat nut |
|
13 | 图纸幅面 | format |
|
14 | 自由弹张量 | free spread |
|
15 | 气膜刚度 | gas film stiffness |
|
16 | 转动手柄 | handle with sleeve |
|
17 | 六角开槽螺母 | hexagon slotted nut |
|
18 | 六角冠状薄螺母 | hexagon thin castle nut |
|
19 | 重要度 | importance |
|
20 | 直线[运动]轴承 | linear [motion] bearing |
|
21 | 板式新边松套法兰 | loose plate flange with lapped pipe end |
|
22 | 弹变空程 | lost motion caused by elastic deflection |
|
23 | 润滑剂相容性 | lubricant compatibility |
|
24 | 长轴半径 | major semi-axis |
|
25 | 高背压式机械密封 | mechanical seal with high back pressure |
|
26 | 弹簧内置式机械密封 | mechanical seal with inside mounted spring |
|
27 | 非致命故障 | non-critical fault |
|
28 | 调速范围 | regulating range |
|
29 | 旋转转矩 | running torque |
|
30 | 磨合磨损 | running-in wear |
|
31 | 副密封 | secondary seal |
|
32 | 冲压方螺母 | square nut without chamfer |
|
33 | 硫化润滑剂 | sulphurized lubricant |
|
34 | 润滑脂脱水收缩 | syneresis of a grease |
|
35 | 机构学 | theory of mechanisms |
|
36 | 双停歇运动 | two-dwell motion,rise-dwell-return-dwell motion |
|
37 | 变刚度弓形板弹簧 | variable rate semi-elliptic spring |
|
38 | 波形弹性垫圈 | wave spring washer |
|
39 | 宽V带 | wide V-belt |
|
40 | 工作极限载荷 | working ultimate load |
|
1 | addendum | 牙顶高 | |
2 | asbestos-free friction material | 无石棉摩擦材料 | |
3 | ASTM viscosity-temperature slope | 黏-温斜率 | |
4 | bi-directional brake | 双向制动器 | |
5 | brake steel belt | 制动钢带 | |
6 | countersunk grooved pin | 沉头槽销 | |
7 | coupling with rubber pads | 橡胶块联轴器 | |
8 | crewed flange | 螺纹法兰 | |
9 | deviation of stroke | 行程偏差 | |
10 | disc handle seat | 圆盘手柄套 | |
11 | dishing | 凹形变形 | |
12 | flat nut | 扁环螺母 | |
13 | format | 图纸幅面 | |
14 | free spread | 自由弹张量 | |
15 | gas film stiffness | 气膜刚度 | |
16 | handle with sleeve | 转动手柄 | |
17 | hexagon slotted nut | 六角开槽螺母 | |
18 | hexagon thin castle nut | 六角冠状薄螺母 | |
19 | importance | 重要度 | |
20 | linear [motion] bearing | 直线[运动]轴承 | |
21 | loose plate flange with lapped pipe end | 板式新边松套法兰 | |
22 | lost motion caused by elastic deflection | 弹变空程 | |
23 | lubricant compatibility | 润滑剂相容性 | |
24 | major semi-axis | 长轴半径 | |
25 | mechanical seal with high back pressure | 高背压式机械密封 | |
26 | mechanical seal with inside mounted spring | 弹簧内置式机械密封 | |
27 | non-critical fault | 非致命故障 | |
28 | regulating range | 调速范围 | |
29 | running torque | 旋转转矩 | |
30 | running-in wear | 磨合磨损 | |
31 | secondary seal | 副密封 | |
32 | square nut without chamfer | 冲压方螺母 | |
33 | sulphurized lubricant | 硫化润滑剂 | |
34 | syneresis of a grease | 润滑脂脱水收缩 | |
35 | theory of mechanisms | 机构学 | |
36 | two-dwell motion,rise-dwell-return-dwell motion | 双停歇运动 | |
37 | variable rate semi-elliptic spring | 变刚度弓形板弹簧 | |
38 | wave spring washer | 波形弹性垫圈 | |
39 | wide V-belt | 宽V带 | |
40 | working ultimate load | 工作极限载荷 |