1 | 实际耗气量 | actual air consumption |
|
2 | 绳索气缸 | cable cylinder |
|
3 | 离心叶轮 | centrifugal wheel |
|
4 | 联接链节 | connecting link |
|
5 | 定转矩试验 | constant torque characteristic test |
|
6 | 可拆链 | detachable chain |
|
7 | 可拆销轴 | detachable connecting pin |
|
8 | 正交场电子束开关管 | electron beam switch tube with cross fields |
|
9 | 喂入昆传动杆 | feed roll driving rod |
|
10 | 平焊位置 | flat position |
|
11 | 十字镐 | hack iron |
|
12 | 哈氏钨铬钴合金 | haynes stellite |
|
13 | 加热再生 | heat regeneration |
|
14 | 可燃空气 | inflammable air |
|
15 | 齿形链 | inverted tooth chain |
|
16 | 顶轴油泵 | jacking oil pump;jacking pump for bearings |
|
17 | 最小实体状态 | least material condition |
|
18 | 载荷钢球 | load ball |
|
19 | 局部自由度 | local degree of freedom,redundant degree of freedom |
|
20 | 复写机 | manifolder;roneo |
|
21 | 中等运转性能 | mid range performance |
|
22 | 管铸造 | pipe casting |
|
23 | 虚约束 | redundant constraint,passive constraint |
|
24 | 反转点动 | reverse inching turning |
|
25 | 高锌黄铜 | reversed brass;mock platina |
|
26 | 顺序阀 | sequence valve,priority valve |
|
27 | 摆动导杆滑块机构 | slider and swing (oscillating)guide-bar mechanism |
|
28 | 球销副 | sphere-pin pair |
|
29 | 起动过载系数 | starting overload ratio |
|
30 | 直边链板 | straight [-sided] link plate |
|
31 | 表面加工系数 | surface machining factor |
|
32 | 铆钉锁头 | tail head |
|
33 | 起重机 | tail tower;crab;a carriage hoist;chain block |
|
34 | 热敏电阻控制器 | thermistor controller |
|
35 | 变电站 | transformer house;electric substation;converting station;transforming plant |
|
36 | 双泵轮液力变矩器 | twin impeller torque converter |
|
37 | 双圆盘波发生器 | two disk wave generator |
|
38 | 升降试验法 | up and down test method |
|
39 | 通流损失 | ventilation losses |
|
40 | 楔角V | wedge angle |
|
1 | actual air consumption | 实际耗气量 | |
2 | cable cylinder | 绳索气缸 | |
3 | centrifugal wheel | 离心叶轮 | |
4 | connecting link | 联接链节 | |
5 | constant torque characteristic test | 定转矩试验 | |
6 | detachable chain | 可拆链 | |
7 | detachable connecting pin | 可拆销轴 | |
8 | electron beam switch tube with cross fields | 正交场电子束开关管 | |
9 | feed roll driving rod | 喂入昆传动杆 | |
10 | flat position | 平焊位置 | |
11 | hack iron | 十字镐 | |
12 | haynes stellite | 哈氏钨铬钴合金 | |
13 | heat regeneration | 加热再生 | |
14 | inflammable air | 可燃空气 | |
15 | inverted tooth chain | 齿形链 | |
16 | jacking oil pump;jacking pump for bearings | 顶轴油泵 | |
17 | least material condition | 最小实体状态 | |
18 | load ball | 载荷钢球 | |
19 | local degree of freedom,redundant degree of freedom | 局部自由度 | |
20 | manifolder;roneo | 复写机 | |
21 | mid range performance | 中等运转性能 | |
22 | pipe casting | 管铸造 | |
23 | redundant constraint,passive constraint | 虚约束 | |
24 | reverse inching turning | 反转点动 | |
25 | reversed brass;mock platina | 高锌黄铜 | |
26 | sequence valve,priority valve | 顺序阀 | |
27 | slider and swing (oscillating)guide-bar mechanism | 摆动导杆滑块机构 | |
28 | sphere-pin pair | 球销副 | |
29 | starting overload ratio | 起动过载系数 | |
30 | straight [-sided] link plate | 直边链板 | |
31 | surface machining factor | 表面加工系数 | |
32 | tail head | 铆钉锁头 | |
33 | tail tower;crab;a carriage hoist;chain block | 起重机 | |
34 | thermistor controller | 热敏电阻控制器 | |
35 | transformer house;electric substation;converting station;transforming plant | 变电站 | |
36 | twin impeller torque converter | 双泵轮液力变矩器 | |
37 | two disk wave generator | 双圆盘波发生器 | |
38 | up and down test method | 升降试验法 | |
39 | ventilation losses | 通流损失 | |
40 | wedge angle | 楔角V |