Caliper: (1)The thickness of a sheet of paper or board, measured with a micrometer and usually expressed in thousandths-of-an inch or in microns.

(1)纸厚,(2)测径器:(1)一张纸或纸板的厚度。用测微讲师度,通常以千分之几寸或微米为单位。

属类：行业术语-印刷-

Hydrothermal Synthesis and Formation Mechanism of Micrometer -sized MoO2 Hollow Spheres

MoO2微米空心球的水热合成及合成机理研究

属类：行业术语-中文论文标题-

Matters Needing Attention of Use and Error Analysis of Micrometer

V形砧千分尺使用注意事项及误差分析

属类：行业术语-中文论文标题-

The adjustment on a micrometer

测微计上的调节器

属类：综合句库--

The design of the most important part of micrometer can be seen in Fig. 2-28

测微器最重要部分的设计见图2-28。

属类：综合句库--

Testing Rotating Error of Shafting with Capacitance Scale Micrometer

电容测微仪测轴系回转误差

属类：行业术语-中文论文标题-

The Calibration of Capacitance-Displacement Micrometer and the Measument of the Magnetostriction Coefficient of Thin Films

电容位移测量仪的校准与薄膜的磁致伸缩测量

属类：行业术语-中文论文标题-

Silicon slices and wafers--Measuring of diameter--Micrometer method

硅片直径测量方法千分尺法

属类：行业标准名称-国家标准名-GB/T14140.2-1993

AEROSPACE SERIES. LUBRICATING DRY FLUOROCARBONATED WITHOUT BINDING MATERIAL OR FILLER, MAXIMUM THICKNESS OF 10 MICROMETER ON METALLIC SUBSTRATE. QUALITY OF COATED PARTS.

航空和航天.最大厚度10千分尺的金属衬底表面用不带有粘结材料或填料的干式氟碳润滑剂.涂层配件的质量

属类：行业标准名称-国际标准-NF L10-200-1995

Verification of geometrical parameters-Micrometers-Part 3: Special design micrometer callipers for external measurement; characteristics, requirements, testing

几何参数检验.千分尺.第3部分:特殊类型的外径千分尺.结构特征,要求,检验

属类：行业标准名称-国际标准-DIN 863-3-1999

Verification of geometrical parameters-Micrometers-Part 1: Standard design micrometer callipers for external measurement; concepts, requirements, testing

几何尺寸的检验.千分尺.第1部分:外径千分尺.标准结构.概念.要求.检验

属类：行业标准名称-国际标准-DIN 863-1-1999

Verification of geometrical parameters-Micrometers-Part 2: Micrometer callipers heads, Depth micrometer; concepts, requirements, testing

几何尺寸的检验.千分尺.第2部分:内径千分尺.深度千分尺.概念.要求.检验

属类：行业标准名称-国际标准-DIN 863-2-1999

Inspector's micrometer caliper

检查用千分卡尺

属类：综合句库--

Check the piston with a micrometer . Compare the sizing-point reading with the measurement of the cylinder diameter taken with an inside micrometer, an outside micrometer and a dial indicator, or a telescope gauge and a micrometer.

可使用千分尺检查活塞,用内径千分尺、外径千分尺和千分表或用内径规和千分尺测量出气缸直径,并与原尺寸标准进行对照。

属类：工程技术-汽车-

Study on the Influence upon Micrometer and Nanometer Mechanism Affected by Quanta Forces

量子力对微、纳米级机构的影响研究

属类：行业术语-中文论文标题-

an eyepiece micrometer

目镜千分尺.

属类：英汉句库--

an inside (outside) micrometer

内径(外径)千分尺.

属类：英汉句库--

Extraction and Microstructure of Sub-micrometer Fe-Cr Fibers

纳米级Fe-Cr纤维的提取和微观结构研究

属类：行业术语-中文论文标题-

Micrometer : An instrument used to measure accurately small distance, thickness, etc.To the nearest 1000th inch or cm.

千分尺:用于精确测量小长度,厚度等的一种仪器,其精确程度达至千分之一寸或厘米。

属类：行业术语-印刷-

micrometer caliper(s)

千分卡尺.

属类：英汉句库--

Depth gauge: (1)Micrometer for measuring etching depth on plates.(2)Typographical ruler for measuring type body or lin e feed. See Type gauge.

深度:一版,一组数字,线表或其他整块材料的垂直量度。

属类：行业术语-印刷-

filar micrometer for use with equatorial telescopes

丝状测微计,与赤道仪一起使用

属类：物品名称-仪表-

PAINTS. DETERMINATION OF DRY FILM THICKNESS. MICROMETER METHOD.

涂料.干涂层厚度的测定.千分尺测量法

属类：行业标准名称-国际标准-NF T30-121-1974

How Does the Outside Micrometer Sleeve Rub Carries on the Repair

外径千分尺套筒摩擦如何进行修理

属类：行业术语-中文论文标题-

Study on Re-location Technique of Micrometer -Size Particles

微粒定位技术研究

属类：行业术语-中文论文标题-

Preparation of Calcium Sulfate Whisker in Micrometer Scale

微米级硫酸钙晶须的制备

属类：行业术语-中文论文标题-

Synthesis of Spherical Micrometer -size Copper Particles

微米级球形铜粉的制备

属类：行业术语-中文论文标题-

Oxidation Resistance and Magnetic Properties of Micrometer Iron Based Fibers

微米级铁基纤维的抗氧化性和磁性

属类：行业术语-中文论文标题-

Fabrication of Micrometer Ni-Cu Alloying Columns by Micro-Anode Guided Electroplating (MAGE)

微阳极导引电镀法制作镍铜合金微柱

属类：行业术语-中文论文标题-

Wear Properties of sub-micrometer SiCp/Al Composites

亚微米SiCp/Al复合材料的磨损性能

属类：行业术语-中文论文标题-